DIY & Pros: Build a 3-Layer Permeable Paver Base to Agency Specs
O'Leary Development GroupSeptember 27, 2026Updated October 16, 2026
Build a 3-layer permeable paver base with a 2-inch bedding. Size for storage or structural load, get sieve reports from suppliers, and prevent long-term...
San Antonio’s Go-To Material Supplier
Get a Free Per-Load Quote Today
Same-day delivery available · Transparent pricing · Licensed & insured
A permeable paver base needs three layers of clean, open-graded stone: a No.2 to No.4 reservoir at the bottom, a No.57 base course above it, and a 2-inch bedding layer of No.8 or 78M stone under the pavers. Size the whole system by calculating both the water storage volume and the structural load capacity, then build to whichever number comes out thicker. Test your soil’s infiltration rate before you order a single ton, because that number decides whether you need underdrains at all.
TL;DR:
The reservoir layer should be a No.2 to No.4 open-graded crushed stone that allows at least 35 to 40 percent porosity and is properly washed and graded.
You must size the base and reservoir layers based on the greater of the water storage volume needed or the structural load requirements, often resulting in depths of 6 to over 12 inches for residential driveways.
Proper installation involves careful site preparation, minimal compaction of the open-graded base, and avoiding contamination, with testing of infiltration rates crucial before material purchase.
Regular maintenance like vacuum sweeping and preventing fines intrusion help sustain permeability, but poorly prepared subgrade or contaminated materials can cause system failure over time.
Always request specific grading reports from suppliers and tailor the design depth to local conditions, especially where weak soil, high groundwater, or heavy loading occur.
Olearydevelopmentgroup
olearydevelopmentgroup.com
Get Stone Delivered to Your Site
O’Leary Development Group delivers bulk gravel, limestone, dirt, topsoil, and landscape stone across San Antonio and surrounding cities.
Every layer in a permeable paver base does a different job, and mixing them up is the fastest way to end up with a driveway that either sinks or refuses to drain. From the bottom up, you’re building a reservoir, a base, and a bedding course, each with its own gradation and purpose.
The reservoir layer (often called subbase) uses open-graded stone in the No.2, No.3, or No.4 range. It sits directly on subgrade and its whole job is storing water until it soaks into the soil or drains out through a pipe. Above that sits the base/choke layer, typically ASTM No.57 stone, which spreads structural load and keeps the finer bedding material from migrating down into the coarser reservoir rock. On top goes the bedding layer, usually No.8, 78M, 89, or 9 gradation stone, screeded to a consistent 2 inches and used to set and lock the pavers themselves.
FHWA’s guidance on permeable interlocking concrete pavement documents porosity in the 35 to 40 percent range for these open-graded layers, meaning a significant portion of the layer’s volume is empty space ready to hold water. That void ratio is the entire reason permeable systems work, and it’s also why gradation control matters so much. A load of “No.57” that’s contaminated with crusher fines or clay might look fine on the truck but will choke off storage capacity fast.
When you order material, ask your supplier for specifics, not just a number:
Washed, angular, crushed stone with less than 2% passing the No.200 sieve
A current sieve or grading report for the specific load being delivered
Confirmation the stone was washed at the quarry or arranged for on-site washing
LA abrasion data if the project spec calls for it, especially for vehicular applications
Rounded river gravel will not lock together the way angular crushed stone does, and it drains less predictably. If a supplier can’t produce a grading report on request, that’s a signal to keep asking questions before the truck shows up.
How Do You Size a Permeable Base and Subbase?
Sizing a permeable paver base is really two separate calculations that happen to use the same layers. One asks how much water you need to store. The other asks how much structural support your traffic load requires. Whichever answer produces a thicker layer wins, a rule FHWA states directly in its PICP design guidance.
Calculate storage volume. Multiply the void ratio of your open-graded stone by the reservoir’s volume. At roughly 40% voids, InTrans and Iowa SUDAS design guidance put the usable storage factor at about 2.5, meaning you need roughly 2.5 inches of stone depth to store 1 inch of design storm water.
Calculate structural depth. This depends on expected traffic (ESALs for vehicular applications) and subgrade strength (CBR or resilient modulus). Weak clay subgrades and heavier vehicle loads both push this number up independently of any storage requirement.
Build to the larger of the two numbers. Don’t average them and don’t split the difference. If storage math says 8 inches but structural math says 11 inches for a driveway carrying delivery trucks, you build 11 inches of open-graded subbase.
Agency examples give you a starting frame of reference. A pedestrian walkway might run with a thin base of just a few inches of No.57 over a modest reservoir. A residential driveway commonly lands in the 6 to 12 inch range for total open-graded depth, a figure Oregon State University Extension’s porous pavement guidance uses for vehicular applications generally. Commercial parking areas with heavier or more frequent loading routinely need deeper sections, sometimes well beyond a foot, particularly where the subgrade CBR is low or the site is asked to store a large design storm.
Ready to Order?
Call Now: 210-983-8005
Same-day delivery available on most orders in San Antonio and surrounding cities
These examples are starting points, not engineered answers. Poor subgrade, high groundwater, or a jurisdiction with an aggressive storm design requirement can push your real number considerably deeper than any generic table suggests.
What’s the Right Construction Sequence for Installing Permeable Pavers?
Getting the materials right doesn’t help if the installation sequence introduces contamination or crushes the very voids you’re relying on for storage. Field handling causes more permeability failures than material selection does, according to InTrans’s pavement subbase design guidance, which points to segregation and improper compaction as the most common culprits.
Prep the subgrade to design grade, install any underdrain piping and its filter/separator layer, and lay geotextile where the spec or soil conditions call for it.
Place the open-graded subbase in lifts, typically 6 to 8 inches loose, spreading with equipment that won’t drive directly on compacted stone and avoiding the temptation to dump and push large piles.
Compact lightly using the guidance in the project spec. Open-graded stone doesn’t compact like dense-graded base. Overdoing it crushes angular particles into fines that then clog the voids you’re depending on.
Screed the bedding layer in a single 2 inch pass, never building it up in multiple thin lifts that create weak planes.
Set edge restraints, lay pavers to pattern, then fill joints and run final compaction passes.
Verify daily tolerances against the project spec before moving to the next area, catching problems while they’re still cheap to fix.
Quality control on site means confirming gradation on delivered loads, checking surface tolerances with a straightedge, and physically keeping soil, mulch, and concrete washout off the exposed base at every stage. San Diego County’s construction specifications call for test sections and documented compaction passes on permeable pavement projects, a habit worth borrowing even on smaller residential jobs.
Pro Tip:Skip the heavy vibratory roller on open-graded layers. A light plate compactor or a few static passes gives you the stability you need without grinding angular stone into fines that quietly choke your drainage.
How Do You Test Soil Before Building a Permeable Base?
Your subgrade decides whether you’re building a full-infiltration system, a partial-exfiltration system with an underdrain, or a fully lined, no-infiltration system that relies entirely on storage and a pipe outlet. Skipping this step is how homeowners end up with a beautiful patio that ponds water for three days after every storm.
Sandy or sandy loam soils generally infiltrate well. Compacted clay or heavily disturbed fill often doesn’t, and running a compactor over subgrade to meet structural requirements can itself cut infiltration rates significantly. A simple percolation test, digging a test hole, filling it with water, and timing the drop, gives you a rough field read before you commit to a design.
Watch for these red flags:
Measured infiltration under 0.5 inches per hour
Groundwater or bedrock within a few feet of the base of your planned excavation
Subgrade that requires structural compaction to meet load requirements, since compaction and infiltration work against each other
Oregon State University Extension recommends testing infiltration before ordering any stone, not after the truck’s already on its way. If your site trips any of those red flags, plan for an underdrain with a controlled outlet elevation rather than betting on native soil to carry the load.
Buying the Right Stone: What to Say to Your Supplier
Ordering permeable paver materials by number alone invites confusion, since gradation names vary slightly between regions and specs. Be specific when you call.
For the reservoir, ask for “washed, open-graded No.2, 3, or 4 crushed stone, less than 2 percent passing the No.200 sieve.”
For the base/choke layer, request “ASTM No.57 crushed limestone, washed, with current gradation report available.”
For bedding, specify “No.8 or 78M washed chip stone, 2-inch screed depth.”
Always ask for a sieve or grading report with the delivery, and confirm the material was washed at the source.
Once material arrives, store it on geotextile or a hard surface, not bare dirt, and never let equipment use the exposed reservoir as a haul road. A base that’s been driven over repeatedly by loaded trucks compacts unevenly and loses storage capacity before a single paver goes down. If you’re sourcing both 3/4 inch base and No.57 for a mixed-depth design, coordinate delivery timing so each lift goes down while the layer below it is still clean.
What Keeps a Permeable Paver Base Working for Years?
A permeable base doesn’t fail overnight. It clogs gradually, usually from things landscaping crews and homeowners do without thinking twice, and the fix is almost always cheaper than the alternative of ripping the whole system back out.
Vacuum sweep the paver surface once or twice a year, more often near trees that drop heavy leaf litter.
Never blow grass clippings, mulch, or bed soil onto the paver surface during routine yard work.
Keep choker and filter layers intact. They exist specifically to stop fines from migrating between layers.
Skip sand bedding entirely. It seals the joints and defeats the purpose of the whole system.
Oregon State’s porous pavement maintenance guidance notes that infiltration rates decline over time on nearly every installation, but systems designed with adequate reservoir storage keep functioning even as surface infiltration slows.
Pro Tip:If your permeable patio sits downhill from a mulched bed, install a small edge barrier or vertical strip of gravel between the two. It’s a five-minute fix that stops years of slow siltation.
Schedule Delivery in Minutes
Get Your Free Quote Today
Tell us your location, access, and estimated yardage — we’ll handle the rest
How O’Leary Development Group Supports Permeable Base Projects
Getting a permeable paver base right starts with getting the right stone on site. O’Leary Development Group delivers washed No.57, No.2/3/4 reservoir stone, and 3/4 inch base material across the San Antonio area, with online quotes and scheduling built for contractors juggling multiple lifts and delivery windows. Ask for a current sieve report on every load and size your delivery lifts to avoid dumping more material than your crew can spread before it segregates.
When Should You DIY a Permeable Base vs. Call a Pro?
A small patio or walkway on decent, well-draining soil is a reasonable DIY project if you have access to the right stone and at least a plate compactor. Once you’re dealing with vehicle loads, questionable subgrade, poor infiltration test results, or any site where standing water is a real liability, it’s worth paying for a geotechnical read and a real structural design. The cost of a soil test is nothing compared to tearing out a driveway that ponds every spring.
— BRIAN
Ready to Order Permeable Paver Base Materials?
Unlike a general aggregate yard where you’re guessing at gradation from a bin label, some suppliers provide transparent per-load pricing and same-day or next-day delivery of washed, open-graded stone sized for permeable applications, whether that’s No.57 base, reservoir stone, or bedding material.
Request a current sieve or grading report when you place your order so you know exactly what’s landing on your site before the truck arrives. Contractors managing multiple lifts across a job can often set up scheduled deliveries and account features to keep material flowing without slowing down the crew. Start by getting a quote for your load or browse the full delivery and hauling service list to line up your reservoir, base, and bedding stone in one call.
Where to Find More Technical Guidance
FHWA’s PICP guidance, best for design thickness rules and material gradation standards
Permeable pavers go over a 2 inch bedding layer of No.8 or 78M stone, which sits on a No.57 base course, which sits on an open-graded No.2 to No.4 reservoir layer at the bottom. FHWA’s PICP guidance documents this three-layer structure with porosity around 35 to 40 percent in the open-graded layers.
What Are the Downsides of Permeable Pavers?
Permeable systems require more upfront design work, including infiltration testing and thicker aggregate sections than a standard paver base, and they need periodic vacuum sweeping to stay effective. They’re also more vulnerable to contamination from tracked-in soil or improper compaction during installation than a conventional dense-graded base.
What Is the Best Base to Put Under Pavers for Permeable Systems?
The best base uses clean, washed, angular crushed stone rather than rounded gravel or anything with significant fines. An ASTM No.57 base layer over an open-graded No.2 to No.4 reservoir gives you the void space needed for storage while still supporting structural loads. Contractors sourcing these materials locally can order washed No.57 stone directly for consistent gradation from load to load.
What Do You Lay Permeable Paving On?
Permeable paving lies on a screeded 2 inch bedding course of open-graded chip stone, never on sand or dense-graded material that would seal the joints and block drainage. That bedding layer sits directly on the compacted base course beneath it, forming the top of the layered system.
How Deep Should a Permeable Paver Base Be?
Depth depends on both storage needs and structural load. Residential driveway applications commonly land in the 6 to 12 inch range for total open-graded depth, a figure Oregon State University Extension uses for general vehicular guidance, but weak subgrade or heavy storm storage requirements can push that considerably deeper.